When we left you last (Installing a Vintage Air Heater with a Stewart-Warner 781 Heater) we had gutted our vintage Stewart-Warner 781 South Wind heater and converted it to a hot air distribution box and a great looking control panel for our Vintage Air Gen II Heater (PN 506101) with defrost unit. The Vintage Air unit would be mounted up behind the original glovebox while the Stewart-Warner unit would mount the controls and distribute some of the hot air.

The Vintage Air heater is a very compact unit with the ability to distribute a large quantity of hot air to the defroster, direct to the floor or blend hot air distribution to both defroster and floor, much like the heater in your modern car. With three fan settings the unit has the ability to provide warmth on a cool day in an open car.

We began this part of the project by disconnecting the battery. Mounting the unit involves some basic fabrication skills. The Vintage Air unit has a mounting plate with four holes attached to the unit. You will notice there is a thin layer of foam rubber between that plate and the actual heater, which prevents vibration being transferred to the car. To mount the unit up high on the inside of the firewall we welded two studs to the inside of the firewall. We did this rather than have bolts showing on the firewall. With these two studs in place we set about fabricating a lower bracket to mount to the firewall and to the two lower bolt holes in the heater mounting plate. The mounts proved to be very sturdy, mounting the heater securely.

After mounting the unit it was time to cut two holes in the firewall using a 1-1/8-inch hole saw. After just a little work with a file we were able to install the two heater hose grommets supplied with the heater. Next we drilled a hole below the hoses and installed a grommet for the main power wire on the heater. We have a grommet assortment we picked up at Harbor Freight and due to the lower shop temperatures and the fact that the assortment is several years old the grommet was a bit stiff. Luckily we have a grommet softening device in our shop (we have also heard some people refer to this tool as a microwave). We took a cap from a spray can, added a bit of water, and dropped the grommet into the water. We then put the cap and water inside the grommet softening device for 40 seconds and out came one very soft grommet. Be careful because the small amount of water is literally boiling hot and that hot water heated the grommet without damaging the rubber. This made installing the grommet much easier.

The next big piece of the puzzle was the wiring. As we mentioned earlier we picked up the main power source right off the firewall-mounted starter solenoid. The Vintage Air wiring includes a circuit breaker so we mounted that next to the solenoid. Keeping the circuit breaker close to the solenoid minimizes the amount of unprotected wire, in our case just 5 inches of wire. Note there is a power in and an accessory side to the circuit breaker and it is marked on the unit. Basically the copper stud is power in, while the silver stud goes to the accessory, in this case the heater.

Following the wiring instructions and schematic (I know, crazy as it seems, reading the instructions actually helps) we routed our wires down to our Stewart-Warner heater box while another set of wires were routed to the passenger side kick panel where it would eventually plug into the heater control valve potentiometer. While the Vintage Air heater is largely plug-and-play, we decided to modify the harness just a bit. We thought it would be best if all wiring could be unplugged outside of our Stewart-Warner heater. This involved cutting and adding a bit of wire to the heater control valve servo harness so the plug would be outside of the Stewart-Warner heater. We used solder and shrink tubing to modify the harness. If you used the control panel supplied in the Vintage Air heater kit you would not have to modify the harness.

Last but not least we had to connect 5/8-inch heater hose from our flathead engine to the heater. The heater comes with some neat 90-degree fittings that seal like an A/C fitting with O-rings. These fittings enable you to angle the hoses nicely. We also employed a molded 90-degree heater hose (Gates PN 28460) to direct the lower hose directly toward the lower hole and grommet in the firewall. We installed the heater control valve in one side of the molded hose and plugged in the Vintage Air wire plug. That completed our installation. Now here is the cool part. By keeping the hoses up tight to the cowl we were able to hide the hoses inside the kick panel, making for a very clean installation and we only sacrificed 1/2 inch of legroom at the firewall.

We did not make our final connections to the engine as we plan on changing the heads and purchasing new Bob Drake water pumps with a heater port. However, we did connect the battery and run the heater through its paces and we can report that the volume of air is impressive. We must admit the louvered South Wind heater may have too many openings aimed away from the passengers. Automotive climate control relies on directing the air onto the occupants. A cure for this would be just use the Stewart-Warner heater as a deco-piece with heater controls and route the hoses from the Vintage Air heater under the dash where they would blow directly on the driver and passenger. Having said all that we feel certain this Vintage Air heater will help keep passengers warm on a cool day and possibly help keep an engine cool on a hot day, after all we are running a Flathead. SRM

3/4 Inch Water Solenoid Valve

Miniature Solenoid Valve, CNC Solenoid Valve, Plastic Solenoid Valve - Baojie,https://www.baojie-pneumatic.com/